WIRE

• 
  C65100 Low Silicon Bronze "B"

  ASTM B98 C65100 is an engineering alloy at least as resistant to corrosion as copper itself, but much stronger, and with good fatigue endurance. 651 Bronze is an alloy noted for its brazeability, strength, corrosion resistance, and electrical properties. C65100 is one of the most weldable copper alloys. It is readily joined by all types of resistance welding. Joining by soldering or brazing is excellent. Joining by gas shielded arc welding and spot welding is also excellent, and by oxyacetylene welding, good. C65100 finds its broadest use as rod and wire for cold headed and roll threaded bolts, wood screws and lag screws. C65100 wood screws and lag screws have unusually high strength and toughness, freedom from embrittlement, and a high degree of corrosion resistance to all types of water, saline fogs, and a wide variety of other corrosives. 651 Bronze hull and deck fastenings are the standard materials with yacht designers and the majority of builders of stock power boats. The alloy is also used for cable connectors, mast tangs, deck and pilot house hardware and equipment, welded fuel and water tanks for pleasure and commercial crafts. It is also one of the best copper alloys for pole line hardware. C65100 nails are also widely used in boat construction and for nailing slate, heavy tile, and other materials where strength and corrosion resistance are essential.
• 
  C51000 CuSn5 Phosphor Bronze Strip

  En equivalent CuSn5 ASTM B139, QQ-B750, SAE J461 C51000 Phosphor Bronze alloy possess a higher yield strength than is readily available in most cast products. Typical applications for phosphor bronze include bearings, bushings, gears, pinions, shafts, thrust washers and valve parts. C51000 Phosphor bronze can be readily brazed or soldered. Capacity for being cold worked is good.
• 
  C27000 Yellow Brass "65%" (CDA 270)

  ASTM B134, SAE J461 Hot-forms more readily and is stronger than C26000.
• 
  C15000 Zirconium Copper
• 
  C51000 Phosphor Bronze "5% A"

  En equivalent CuSn5 ASTM B139, QQ-B750, SAE J461 C51000 Phosphor Bronze alloy possess a higher yield strength than is readily available in most cast products. Typical applications for phosphor bronze include bearings, bushings, gears, pinions, shafts, thrust washers and valve parts. C51000 Phosphor bronze can be readily brazed or soldered. Capacity for being cold worked is good.
• 
  C10200 Oxygen Free Copper (CDA 102)

  UNS CDA 102, SAE J461, ASTM B152, ASTM B187, ASTM B272 High Conductivity (OFHC) Copper characteristics are high ductility, high electrical and thermal conductivity, high impact strength, good creep resistance, ease of welding, and low volatility under high vacuum. TYPICAL USES FOR C10200 OXYGEN FREE COPPER: ELECTRICAL: Electrical Conductors, Klystrons, Microwave Tubes, Transistor Components, Lead In Wire, Coaxial Cables, Copper to Glass Seals in Electronic Appliances, Busbars, Bus Conductors, Wave Guides INDUSTRIAL: Tubing, LP Gas Service, Tubing, Medical Gas- Oxygen, Vacuum Seals, Coaxial Tube, Billet Mold Tube, Extrusion Cans for Powder Metallurgy
• 
  C27000 Yellow Brass "65%" (CDA 270)

  ASTM B134, SAE J461 Hot-forms more readily and is stronger than C26000.
• 
  C26000 Cartridge Brass "70/30" (CDA 260)

  ASTM B36 (Bar, Sheet, and Plate), ASTM B135 (Tubing), SAE J461 EN equivalent for this alloy CuZn30